Get more power out of your Catalyst with this one simple mod! Our stage...
Get more power out of your Catalyst with this one simple mod! Our stage...
New for your 2024+ Catalyst! the PROMAX Front bumper Is the ultimate...
FOR CATALYST ODELS WITH ADAPT CLUTCHES, 2024+ MODEL YEAR! INCLUDES...
All the hardware you need when narrowing your 40" or 38" arctic cat to the new 36" front suspension! Includes: 36" width tie rods (re-use stock rod ends) Rod ends for new style upper arms with shoulder bolts & nuts Shock spacer for FOX FLOAT shocks to shorten from 38" length to 36" length All the hardware you need when...
Check out our new extruded XXX framed rear bumper with led tail light for the Arctic Cat and Yamaha mountain sleds! This new bumper is like no other! The XXX side frames of the aluminum bumper is extruded and then machined to the correct shapes. The design with the three X's provides tremendous added strength to the tunnel. Check out our new extruded XXX framed...
Good used Crank Case with a Rebuilt Crank directly from Northern Crank. Please read core charge requirements below. Good used Crank Case with a Rebuilt...
Good used Crank Case, Rebuilt Crank directly from Northern Crank, New Updated OEM Pistons, Honed Cylinders in Excellent Condition, Brand New Head, Rebuilt with Complete Cometic Gasket Kit Please read core charge requirements below. Good used Crank Case, Rebuilt Crank...
Our BDX tie rod is stronger than the oem tie rods. It has a larger diameter tube, yet still has the flats machined in it so you put a wrench on to adjust. A great option for your 2016 and newer Arctic Cat mountain sled or Yamaha MountainMax800 with factory 36 inch stance. Our BDX tie rod is stronger than the...
ARCTIC CAT CTEC 600 FLYWHEEL, FITS ALL 2014-CURRENT 600 CTEC MODELS. RETAIL IS OVER $1000 ON THIS PART! GREAT DEAL! OEM PART # 0902-026 ARCTIC CAT CTEC 600 FLYWHEEL, FITS...
A direct replacement for a fraction of the price. This pipe sensor identical to the 2011-current Arctic Cat OEM Pipe Temp Sensor that is known to be prone to failure. Why block it off when you can have a working sensor for a fraction of the price! A direct replacement for a fraction...
EVERYTHING you need to replace your TEAM primary Clutch with the better performing, lighter, narrower ADAPT Clutch! Now with our Updated HEAVY DUTY Roller Bushings Installed! Direct Upgrade for all 2016+ Team BOSS Secondary Clutches Kit includes: 0746-933 ADAPT Clutch Pro-Mag Adjustable weights Titanium Clutch Bolt & washer EVERYTHING you need to replace your...
C3 SyncroDrive for the 2012-15 Arctic Cat 800 Proclimb / ProCross. You will have the following benefits from this system. 1250 Grams (2.75 lb) less rotating mass 12 lb weight savings (18 lb with oil delete) Currently available in Gear Ratios from 1.50 to 2.63 No break in period Gear and belt changes in minutes Inexpensive 8mm pitch belts... C3 SyncroDrive for the 2012-15 Arctic...
SyncroDrive for All the Ctec 600/800 Non Drop/Roll Models You will have the following benefits from this system. 1250 Grams (2.75 lb) less rotating mass 12 lb weight savings (18 lb with oil delete) Currently available in Gear Ratios from 1.50 to 2.63 No break in period Gear and belt changes in minutes Inexpensive 8mm pitch belts SyncroDrive for All the Ctec 600/800...
For all Arctic cats with the TEAM BOSS Secondary (2016-21) We have them in multi angles and straight angles. If you don't see the angle you want on the drop down menu, just pick "custom" and put the special angle you want in the message section when ordering online. We make these in house so that you can get exactly what you need all of the time!... For all Arctic cats with the TEAM...
Sealed Jackshaft bearings for chaincase and clutch sides on all 2012-current 23 arctic cat models Sealed Jackshaft bearings for...
19 TOOTH HYVO ARCTIC CAT GEARS, fits all 2012- current models with 13 wide HYVO chain and small 19 Spline jackshaft, will not for 2018+ models with larger splined hollow shaft Normal Price $22.99 Our Price $21.95 19 TOOTH HYVO ARCTIC CAT GEARS, fits...
Lose over 0.85 lb of rotating mass of your machine with this one part making it the lightest on the market! Drop in, ready to go with rollers and snap rings installed and comes with a thrust washer for your secondary spring to prevent wear and prolong spring life. Machined from 7075 Aluminum and hard-coat anodized to ensure an ultra strong part that will... Lose over 0.85 lb of rotating mass of...