BRAND NEW TEAM DRIVE CLUTCH FOR 2018+ ARCTIC CAT 800 AND 600 MODELS WITH...
Replacement lower A arms for Arctic Cat and Yamaha snowmobiles with the...
Steering Tie Rods for Arctic Cat models with 36" front ends. Also...
Our aluminum charge tube kits dissipates heat better than stock rubber...
Our aluminum charge tube kits dissipates heat better than stock rubber...
This Billet manifold moves your fuel injectors from the cylinder to the...
This Billet manifold moves your fuel injectors from the cylinder to the...
This nice back lit Wideband Air/Fuel Ratio Gauge will give you precise information on your engine. This will help you determine if your engine is running rich or lean. Very good engine tuning tool. ON SALE!! SAVE 30!! This nice back lit Wideband Air/Fuel...
This nice dual exhaust temperature gauge will give you precious informations on your engine. The settable warning for each cylinder give the opportunity to set the maximum temperature to reach at up to 2100°F. The color change and the blinking of the screen makes it very easy to see if something is going wrong with the engine. ON SALE NOW!! SAVE $30!! This nice dual exhaust temperature...
This nice dual exhaust temperature gauge will give you precious informations on your engine.The settable warning for each cylinder give the opportunity to set the maximum temperature to reach at up to 2100°F. The color change and the blinking of the screen makes it very easy to see if something is going wrong with the engine. ON SALE NOW!! SAVE $35!! This nice dual exhaust temperature...
TWO STROKE PIPE SENSOR ADAPTOR, for wide band 02 sensors when used on 2 stoke engines. Extends the life of the sensor and prevents premature failure. TWO STROKE PIPE SENSOR ADAPTOR, for...
WELD ON BUSHING FOR EGT SENSORS WELD ON BUSHING FOR EGT SENSORS
2.5in wheel with sealed 5/8ID bearing. 2.5in wheel with sealed 5/8ID bearing.
2.7 INCH REPLACEMENT WHEEL WITH SEALED BEARING 5/8" 2.7 INCH REPLACEMENT WHEEL WITH...
Want to take your front stock idlers off without abnormal hi-fax wearing? This is the kit you need. Fits 2007-2019 X-Fires and M Series. CURRENTLY OUT OF STOCK************** Want to take your front stock idlers...
Lite Weight trackshaft is 1pound less than stock trackshaft. Fit's 2012-Up ProClimb/ ProCross. Also fits Yamaha Viper and Sidewinder This shaft is very strong and has been used by several 600+ horsepower race sleds. Lite Weight trackshaft is 1pound less...
Track ratcheting? Old extroverts worn? Try out Xtreme 8 tooth extroverts! Fits all Diamond Drive trackshafts. 3.0 pitch. Fits Arctic Cat 2004 and newer diamond drive sleds, Arctic Cat 2012 and newer. Yamaha Viper, plus Sidewinder. Fits 1 3/4" hex shaft Track ratcheting? Old extroverts...
Old drivers worn? Try our Xtreme 9 tooth drivers! Fits all Diamond Drive trackshafts. 2.52 pitch Also fits all Arctic Cat ProCross / ProClimb, and Yamaha Sidewinder and Viper. Old drivers worn? Try our Xtreme 9...
Worn drivers? Do you have 9 tooth drivers and want more speed?? Try our Xtreme 10 tooth drivers! Fits all Diamond Drive trackshafts. 2.52 pitch Worn drivers? Do you have 9 tooth...
Top quality heavy clutch pullers for your snowmobiles. One piece design, precision machined, and heat treated for strength. This model fits all 2010 and newer models, and 2007 and newer 1000 twin and 1100 4 strokes. Also fits: Wildcat UTVs, X and XX Yamaha MountainMax 800 2021 Top quality heavy clutch pullers for...
Our mountain series billet heads bolt on some serious power for your Arctic Cat 6000 motor. It is designed to run on premium pump gas when ran above 4000 ft altitude. Huge torque gains to provide the grunt you need and want for boondocking and climbing. Much quicker throttle response! 6-7 horsepower peak and in the mid range! These heads work extremely... Our mountain series billet heads bolt...
PRO-COOL billet heads bolt on some serious power for your snowmobile. The low altitude versions provide extra cooling capacity; they look great, and bolt on power. They add 3-4 peak horsepower with a lot of mid-range grunt too. PRO-COOL heads run on premium pump gas, 91 or higher octane. This high quality machined kit comes with a billet head cover and... PRO-COOL billet heads bolt on some...
Sick of your pipe sensor going bad on your machine? You can bypass the sensor with this plug in resister block off. Then you don't need to run the pipe sensor anymore. This is a lot less money than the stock sensor too. Sick of your pipe sensor going bad on...
Whether you have a stock front end or our new PRO-Lite Forged front end, you can upgrade your lower A arms with these Chrome Moly versions. They are arched for extra clearance to help prevent hitting rocks and stumps. The Chrome Moly material is also very strong. The weight is about the same as stock, but better of course. CURRENTLY OUT OF STOCK, DUE... Whether you have a stock front end or...
For Arctic Cats with Team clutches is our Pro Mag adjustable weights that are adjustable from 64-86 grams. They have 4 positions per weight arm with easy to use magnets. This allows you have proportion the weight just the way you want it, whether you want a light or heavy tip weight. And our price is even much less than a stock un adjustable weights. For Arctic Cats with Team clutches is...
Finally, a simple bolt on coupling device for boosted Arcitc Cats and Yamaha SR Vipers. Simple effective and priced right. Simply turn the blocks to a new position to go from no coupling (Stock) to the available positions. Our moto for this item (Keep It Simple Stupid) give you the option of having some or no coupling with a simple adjustment. All parts... Finally, a simple bolt on coupling...
We have been using power commanders for years. They are very precise and work extremely well. They sense true throttle position and rpm ranges to fine tune the maps. The auto tune can be added or the POD-300 gauge to monitor air fuel ratios, data logging and change to multiple maps. When you purchase from us we will put the map into it for our products... We have been using power commanders...
This version is a "universal fit", single O2 sensor kit. It can be used on any vehicle that has a PCV installed on it. It comes with a single O2 sensor, "cut to length" sensor cable, control module, O2 sensor, one weld boss kit, a CAN connection cable, and CAN termination plug. It requires a ground and +12 volt connection to be made using the supplied... This version is a "universal fit",...
The POD-300 is an accessory display for Dynojet devices that support DJ-CAN; including the popular Power Commander V, AutoTune, WideBand 2, and CMD. The POD-300 is an accessory display...
POD-300 Handlebar Mount Kit, BLACK POD-300 Handlebar Mount Kit, BLACK
Use this map switch to toggle between dual maps on your power commander Use this map switch to toggle between...
Xtreme LiteWeight Seat! This new Taller version of our seat people really like! It sits flat on top, is very light and very comfortable. Some people prefer the taller seat you can use your leg pushing against if for leverage when leaning the sled over. With easy access storage compartment in back. NEW LOWER PRICE!!! Lighter than stock seat. Xtreme LiteWeight Seat! This new...